The following solar LED street light manufacturers summarize the solutions for several solar street lights installation errors. Solution: Before installation, try to stay away from the light source to avoid interference. If it is unavoidable, ensure that there are Customize led street lights Manufacturers no obstructions in the south direction of solar street lights.

 

If you do not pay attention to some important details during the installation process, it will naturally cause the solar street light to not light up normally. The price is naturally much higher than that of cold galvanized. The corners of complex workpieces are prone to 'electric burning' and become grayish, where the zinc layer is thicker.

 

The current dead angle is easy to form in the negative corner, resulting in an undercurrent gray area, where the zinc layer is thinner. In the same way, 'you get what you pay for', solar street lights hot-dip galvanizing are more worth buying. After degreasing and pickling with electrolytic equipment, the workpiece is put into a solution of zinc salt and connected to the negative electrode of the electrolytic equipment.

 

The electroplated layer using the white passivation process is bluish-white or white with green light, and the electroplating layer of the white passivation process is slightly colorful at a certain angle with the sunlight. Compared with cold galvanizing, hot-dip galvanizing has a higher cost and a more complicated manufacturing process than cold galvanizing.. 

Megosztás a facebookon

Now, we can complete the debugging in a second or two on the console. From the screenshots at night, it is clear which street light is on or not and how bright it is. Starting in 2013, our city began to try to carry out energy-saving transformation of street lamps, and gradually changed the traditional high-pressure sodium lamps and metal halide lamps to green, energy-saving LED lamps according to the idea of ​​'aging a batch, transforming a batch'.

 

In the past, our inspectors needed to run around the city to check the lighting of the street lights, so it is inevitable that faulty street lights cannot be repaired in time. The former hand-controlled controller has been laid off, replaced by a high-tech intelligent management terminal. In the city and town street light management office, in a room full of high-tech equipment, I saw that the staff were 'remotely monitoring' street lights.

 

On July 100W led street light 18, 2014, our city included more than 3,500 LED street lamps in the urban area as the first batch to be included in the street lamp monitoring intelligent monitoring management system. Currently, there are more than 630 monitoring points in the city.

 

After receiving the alarm information, the central main control computer will display the fault location and fault type, and can accurately locate the street lamp location on the map and complete the maintenance dispatch in time.After years of hard work, the LED street lights on the main roads in the urban area of ​​Gaoyou City have all completed the 'green transformation', and the towns (streets) have also been fully rolled out.

 

After being incorporated into the street lamp monitoring intelligent monitoring management system, each lamp can automatically switch and adjust the brightness of each lamp according to factors such as sunshine time, weather, traffic flow and traffic flow. According to the staff, he is operating the street lamp monitoring intelligent management system

Megosztás a facebookon

The heat dissipation and protection of LED lamps is an industry-specific problem. From the analysis of thermal energy, heat (Q) a divergent power PD;UF;IF because when the I)ED efficiency reaches the standard value, the relative change of UF and IF is relatively small. Therefore, when a large number of LEDs are placed on a module, it will increase the difficulty of heat treatment.

The problem is that this heat will cause the temperature of the LED module to rise, and the increase in temperature will cause the T working voltage of the LED to decrease, and the intensity of light will decrease. The effect of heat dissipation design on LED life. With the increase in temperature, the LED light decays or even Damaged, the driver is also damaged due to over temperature, reducing the reliability and service life of the LED lamps. And affect the efficiency of the LED driver, damage the life of the magnetic components and output capacitors, reduce the reliability of the LED driver, and seriously reduce the life of the LED, and accelerate the light decay of the LED.

When designing LED lamps, good heat dissipation design is mainly due to The following considerations: Improve the luminous efficiency Waterproof Led Garden Light of the LED, increase the current (power), and reduce the junction temperature (Tj) of the LED chip. LEDs with high optical performance and high reliability depend on the junction temperature (Tj) of the LED chip. Among them, conduction and convection are more important for the heat dissipation of LED garden lights, and divergence is not important.

Therefore, a good thermal design is to manage the LED junction temperature Tj. Due to the low output beam of a single LED at this stage, for general lighting use, a large number of LED components are required to be placed in a module to achieve the required illuminance. In the case, the heat generated during the operation of the lamp cannot be dissipated into the air, which causes the LED module and drive circuit to work in an extremely harsh environment..The system should be optimized in the material selection structure design to solve the contradiction between the heat dissipation and product protection of LED lamps

Megosztás a facebookon

Generally, there will be no water. Therefore, the key consideration in the design is the connection between the battery module bracket and the solar LED street light pole. In the above formula, r is the inner diameter of the ring, is the width of the ring.If the wind resistance coefficient is selected as 27m/s (equivalent to a tenth typhoon), according to the non-viscous fluid mechanics, the wind pressure on the battery module is only 365Pa.

Therefore, during construction, attention should be paid to bend the internal connecting wire of the controller terminal into a type and fix it, and the connecting wire exposed to the outside shall also be fixed to a type, so that rainwater cannot enter and cause the controller to short-circuit , In addition, waterproof glue can be applied to the inner and outer line interfaces to waterproof.

The wind resistance design is mainly divided into two parts, one is the wind resistance design of the battery module bracket, and the other Outdoor Aluminum Led Light Housing manufacturers is the wind resistance design of the light pole.Anti-theft design of solar LED street lamp system In places far away from the city, you should also pay attention to anti-theft work. The distance between the calculation point P of the resistance moment W of the failure surface of the solar led street light pole and the load F of the solar panel on the pole is PQ = [5000+(168+6)/tan16o; Sin16o =1545mm=1.

Therefore, the component itself can withstand the wind speed of 27m/s without being damaged. However, in some actual engineering cases, the rainwater will run down the outside of the controller terminal because of improper installation. According to mathematical derivation, the resistance moment of the circular failure surface.Wind resistance design of solar LED street lamp system In the solar led street light system, a structural issue that needs to be paid attention to is the wind resistance design. Buried solar led street light batteries with cement is an effective anti-theft measure.  

Megosztás a facebookon

Since solar street lights do not need to consume any energy later, the cost will be recovered quickly. Therefore, it is most important to choose a suitable light source for road lighting. In terms of service life, LED lamp beads are used, so there is little difference between the two street lamps in terms of the service life of the light source.

Comparing the two, the mains LED street lights have lower energy consumption and longer service life than traditional energy-saving lamps.

In case you need it in the future. is a manufacturer specializing in the production of solar street lights, high pole lights, garden lights, landscape lights, led street lights, more than 15 years of production experience, high quality, low prices, honesty, and welcomes new and old customers Come to consult.As a new solar energy product in daily life, solar street lights, as a consumer, how much do you know about it? , The following will give you a brief introduction to the actual configuration parameters of solar street lights from Qiandu Lighting.

Regarding the actual configuration parameter conditions of solar street lights, you can first determine the height of the light pole according to the width of the road; then determine the power of the light source according to the actual lighting demand and the height of the light pole; the other is the local daily time and night street light lighting time to make led garden light street lights The detailed configuration between the components ensures the stability of the system

Megosztás a facebookon

Regardless of production, use and scrap, they do not contain or produce any toxic and harmful heavy metal elements and substances such as lead, mercury, and cadmium., Ltd. They have high storage energy density, reaching 460-600Wh/kg, which is about 6-7 times that of lead-acid batteries. The self-discharge rate is very low, and the storage of electric energy can ensure the night lighting of solar street lights.

Lithium batteries have the following advantages as storage point batteries for solar street lights. The most important thing is the environmental protection of lithium batteries. The service life is long, and the service life can reach more than 6 years. currently has independent research and development projects including new high-power LED lamps, various styles of outdoor lighting lamps, etc.As the energy crisis continues to intensify and people’s awareness of environmental protection continues to increase, more and more cities will choose solar street lights when they are building street led high bay light lights. 

At present, batteries are divided into many types, including nickel-chromium, nickel-metal hydride, lithium batteries, etc., and has a number of patented products., and when it comes to the best storage performance for electric energy, lithium batteries. If you want to know the specific price of lithium battery solar lights, you can contact us for detailed consultation or project inspection.. And for many people, how about the price of lithium battery solar street lights with so many advantages?

In fact, the domestic technology of lithium battery solar street lights is relatively mature, not only the quality of the finished products is higher, but the price is relatively cheaper than traditional street lights, and it can also achieve environmental protection and energy saving.

The most important technology for solar street lights to achieve true energy conservation and environmental protection is not only The absorption and conversion technology of solar energy is also important to the storage of electric energy after solar energy conversion. High and low temperature adaptability, can be used in the environment of -20 ℃--60 ℃, to adapt to different environments to ensure normal work

Megosztás a facebookon